List of ASTM Standard 12401 to 12500
ASTM D 7704-12 : Standard Test Method for Total Aldehydes in Styrene Monomer by Potentiometric Titration
ASTM D 7705/D 7705M-12 : Standard Test Method for Alkali Resistance of Fiber Reinforced Polymer (FRP) Matrix Composite Bars used in Concrete Construction
ASTM D 7706-11 : Standard Practice for Rapid Screening of VOC Emissions from Products Using Micro-Scale Chambers
ASTM D 7707-11 : Standard Specification for Wipe Sampling Materials for Beryllium in Surface Dust
ASTM D 7708-11 : Standard Test Method for Microscopical Determination of the Reflectance of Vitrinite Dispersed in Sedimentary Rocks
ASTM D 7709-12 : Standard Test Methods for Measuring Water Vapor Transmission Rate (WVTR) of Pharmaceutical Bottles and Blisters
ASTM D 7711-11e1 : Standard Guide for Description of Polymer Pellet Defects
ASTM D 7712-11 : Standard Terminology for Sampling and Analysis of Asbestos
ASTM D 7713-12 : Standard Specification for Aqueous Engine Coolant Grade Glycol (53% Nominal)
ASTM D 7714-11 : Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
ASTM D 7715-12 : Standard Specification for Fully-Formulated Glycerin Base Engine Coolant for Heavy-Duty Engines
ASTM D 7716-11a : Standard Test Method for Determination of Residual Methanol in Glycerin by Gas Chromatography
ASTM D 7717-11 : Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory Analysis
ASTM D 7718-11 : Standard Practice for Obtaining In-Service Samples of Lubricating Grease
ASTM D 7719-14a : Standard Specification for High-Octane Unleaded Fuel
ASTM D 7720-11 : Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination
ASTM D 7721-11 : Standard Practice for Determining the Effect of Fluid Selection on Hydraulic System or Component Efficiency
ASTM D 7722-13 : Standard Terminology Relating to Industrial Textile Stitches and Seams
ASTM D 7723-11 : Standard Test Method for Rubber Property<char: emdash>Macro-Dispersion of Fillers in Compounds
ASTM D 7724-11 : Standard Test Method for Carbon Black<char: emdash>Non-Dispersible Matter by Mechanical Flushing (NDM)
ASTM D 7725-12 : Standard Test Method for the Continuous Measurement of Turbidity Above 1 Turbidity Unit (TU)
ASTM D 7726-11 : Standard Guide for The Use of Various Turbidimeter Technologies for Measurement of Turbidity in Water
ASTM D 7727-11E1 : Standard Practice for Calculation of Dose Equivalent Xenon (DEX) for Radioactive Xenon Fission Products in Reactor Coolant
ASTM D 7728-11 : Standard Guide for Selection of ASTM Analytical Methods for Implementation of International Cyanide Management Code Guidance
ASTM D 7729-12 : Standard Practice for Determining and Expressing Precision of Measurement Results, in the Analysis of Water, as Relative Standard Deviation, Utilizing DQCALC Software
ASTM D 7730-11 : Standard Test Method for Determination of Dioctyl Sulfosuccinate in Sea Water by Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS)
ASTM D 7731-11e1 : Standard Test Method for Determination of Dipropylene Glycol Monobutyl Ether and Ethylene Glycol Monobutyl Ether in Sea Water by Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS)
ASTM D 7733-12 : Standard Specification for Acrylic Dispersion Ground
ASTM D 7734/D 7734M-13 : Standard Test Method for Determination of Open Time of Oxidative Printing Inks and Overprint Varnishes by a Manual Method
ASTM D 7735-11E1 : Standard Test Method for Type A Durometer Hardness Testing of Road Marking Thermoplastic at Elevated Temperatures
ASTM D 7736-12 : Standard Test Method for Determination of Acids and Glycol Esters in Ethylene Glycol
ASTM D 7737-11 : Standard Test Method for Individual Geogrid Junction Strength
ASTM D 7739-11 : Standard Practice for Thermal Oxidative Stability Measurement via Quartz Crystal Microbalance
ASTM D 7740-11 : Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants
ASTM D 7741/D 7741M-11e1 : Standard Test Method for Measurement of Apparent Viscosity of Asphalt-Rubber or Other Asphalt Binders by Using a Rotational Hand Held Viscometer
ASTM D 7742-11 : Standard Practice for Determination of Nonylphenol Polyethoxylates (NPnEO, 3 ≤ n ≤ 18) and Octylphenol Polyethoxylates (OPnEO, 2 ≤ n ≤ n ≤ 12 in Water by Single Reaction Monitoring (SRM) Liquid Chromatography/ Tan
ASTM D 7743-12 : Standard Test Method for Measuring the Minimum Fluidization Velocities of Free Flowing Powders
ASTM D 7744/D 7744M-11 : Standard Test Methods for Tensile Testing of High Performance Polyethylene Tapes
ASTM D 7745-11 : Standard Practice for Testing Pultruded Composites
ASTM D 7746-11 : Standard Practice for Calculating the Superimposed Load on Wood-frame Floor-Ceiling Assemblies for Standard Fire-Resistance Tests
ASTM D 7747/D 7747M-11E1 : Standard Test Method for Determining Integrity of Seams Produced Using Thermo-Fusion Methods for Reinforced Geomembranes by the Strip Tensile Method
ASTM D 7748/D 7748M-14 : Standard Test Method for Flexural Rigidity of Geogrids, Geotextiles and Related Products
ASTM D 7749-11 : Standard Test Method for Determining Integrity of Seams Produced Using Thermo-Fusion Methods for Reinforced Geomembranes by the Grab Method
ASTM D 7750-12 : Standard Test Method for Cure Behavior of Thermosetting Resins by Dynamic Mechanical Procedures using an Encapsulated Specimen Rheometer
ASTM D 7751-12 : Standard Test Method for Determination of Additive Elements in Lubricating Oils by EDXRF Analysis
ASTM D 7752-11 : Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids
ASTM D 7753-12 : Standard Test Method for Hydrocarbon Types and Benzene in Light Petroleum Distillates by Gas Chromatography
ASTM D 7754-11 : Standard Test Method for Determination of Trace Oxygenates in Automotive Spark-Ignition Engine Fuel by Multidimensional Gas Chromatography
ASTM D 7755-11 : Standard Practice for Determining the Wear Volume on Standard Test Pieces Used by High-Frequency, Linear-Oscillation (SRV) Test Machine
ASTM D 7756-13 : Standard Test Method for Residues in Liquefied Petroleum (LP) Gases by Gas Chromatography with Liquid, On-Column Injection
ASTM D 7757-12 : Standard Test Method for Silicon in Gasoline and Related Products by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry
ASTM D 7758-11 : Standard Practice for Passive Soil Gas Sampling in the Vadose Zone for Source Identification, Spatial Variability Assessment, Monitoring, and Vapor Intrusion Evaluations
ASTM D 7759/D 7759M-14 : Standard Guide for Nuclear Surface Moisture and Density Gauge Calibration
ASTM D 7760-12 : Standard Test Method for Measurement of Hydraulic Conductivity of Tire Derived Aggregates Using a Rigid Wall Permeameter
ASTM D 7762-11 : Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash
ASTM D 7764-12 : Standard Practice for Pre-Installation Acceptance Testing of Vibrating Wire Piezometers
ASTM D 7765-12 : Standard Practice for Use of Foundry Sand in Structural Fill and Embankments
ASTM D 7766/D 7766M-11 : Standard Practice for Damage Resistance Testing of Sandwich Constructions
ASTM D 7767-11 : Standard Test Method to Measure Volatiles from Radiation Curable Acrylate Monomers, Oligomers, and Blends and Thin Coatings Made from Them
ASTM D 7768-12 : Standard Test Method for Speciated Organic Volatile Content of Waterborne Multi- Component Coatings by Gas Chromatography
ASTM D 7770-12 : Standard Test Method for Collection of Volatile Organic Compounds Emitted During Simulated Manufacturing of Engineered Wood Products Via a Sealed Caul Plate Method
ASTM D 7771-13 : Standard Test Method for Determination of Benzo-α-Pyrene (BaP) Content in Carbon Black
ASTM D 7772-11 : Standard Test Method for Carbon Black Extractables – Absorbance of Cyclohexane Extract
ASTM D 7773-12 : Standard Test Method for Determination of Volatile Inorganic Acids (HCl, HBr, and HNO<inf>3 </inf>) Using Filter Sampling and Suppressed Ion Chromatography
ASTM D 7774-12 : Standard Test Method for Flexural Fatigue Properties of Plastics
ASTM D 7775-11e1 : Standard Guide for Measurements on Small Graphite Specimens
ASTM D 7776-12 : Standard Guide for Self-Assessment of Quality System Practices in Petroleum Products and Lubricant Testing Laboratories
ASTM D 7777-13 : Standard Test Method for Density, Relative Density, or API Gravity of Liquid Petroleum by Portable Digital Density Meter
ASTM D 7778-12 : Standard Guide for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D 7779-11 : Standard Test Method for Determination of Fracture Toughness of Graphite at Ambient Temperature
ASTM D 7780-12 : Standard Practice for Geospatial Data for Representing Coal Mining Features
ASTM D 7781-14 : Standard Test Method for Nitrite-Nitrate in Water by Nitrate Reductase
ASTM D 7782-13 : Standard Practice for Determination of the 99 %/95 % Critical Level (WCL) and a Reliable Detection Estimate (WDE) Based on Withinlaboratory Data
ASTM D 7783-13 : Standard Practice for Within-laboratory Quantitation Estimation (WQE)
ASTM D 7784-12 : Standard Practice for the Rapid Assessment of Gamma-ray Emitting Radionuclides in Environmental Media by Gamma Spectrometry
ASTM D 7785-12 : Standard Test Method for Water in Lint Cotton by Oven Evaporation Combined with Volumetric Karl Fischer Titration
ASTM D 7786-13 : Standard Test Method for Determining Enamel Holdout
ASTM D 7787/D 7787M-13 : Standard Practice for Selecting Wood Substrates for Weathering Evaluations of Architectural Coatings
ASTM D 7789-12 : Standard Practice for Collection of Fungal Material from Surfaces by Swab
ASTM D 7790-12 : Standard Guide for Preparation of Plastic Packagings Containing Liquids for United Nations (UN) Drop Testing
ASTM D 7791-12 : Standard Test Method for Uniaxial Fatigue Properties of Plastics
ASTM D 7793-13 : Standard Specification for Insulated Vinyl Siding
ASTM D 7794-12 : Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines
ASTM D 7795-12 : Standard Test Method for Acidity in Ethanol and Ethanol Blends by Titration
ASTM D 7796-12 : Standard Test Method for Analysis of Ethyl tert-Butyl Ether (ETBE) by Gas Chromatography
ASTM D 7797-12 : Test Method for Determination of the Fatty Acid Methyl Esters Content of Aviation Turbine Fuel Using Flow Analysis by Fourier Transform Infrared Spectroscopy – Rapid Screening Method
ASTM D 7798-13 : Standard Test Method for Boiling Range Distribution of Petroleum Distillates with Final Boiling Points up to 538°C by Ultra Fast Gas Chromatography (UF GC)
ASTM D 7799-12A : Standard Specification for Tufted and Woven Broadloom Carpet Adhesives Without Homogenous PVC or Non-PVC Backings
ASTM D 7801-12 : Standard Terminology for Paint Brush Application Tools
ASTM D 7802-12 : Standard Terminology for Paint Roller Application Tools
ASTM D 7803-12 : Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and Steel Product and Hardware Surfaces for Powder Coating
ASTM D 7804-12 : Standard Test Method for Fiber Shedding of Paint Roller Covers
ASTM D 7805-13 : Standard Terminology for Printing Ink Vehicles and Related Materials
ASTM D 7806-12 : Standard Test Method for Determination of the Fatty Acid Methyl Ester (FAME) Content of a Blend of Biodiesel and Petroleum-Based Diesel Fuel Oil Using Mid-Infrared Spectroscopy
ASTM D 7807-12 : Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection
ASTM D 7808-12 : Standard Practice for Determining the Site Precision of a Process Stream Analyzer on Process Stream Material
ASTM D 7811-13 : Standard Test Method for Bow and Skew Using a Measuring Tool
ASTM D 7815-12 : Standard Practice for Handling, Transportation, and Storage of Halon 1211, Bromochlorodifluoromethane (CF2BrCl)
ASTM D 7816-12 : Standard Test Method for Enumeration of Halophilic and Proteolytic Bacteria in Raceway Brine, Brine-Cured Hides and Skins
ASTM D 7817-12 : Standard Test Method for Enumeration of Yeast and Mold in Raceway Brine, Brine- Cured Hides and Skins