List of ASTM Standard 8001 to 8100
ASTM F 2730/F 2730M-14 : Standard Specification for Silicon Nitride Cylindrical Bearing Rollers
ASTM E 2730-10 : Standard Practice for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits
ASTM E 2731-09 : Standard Specification for Materials to Mitigate the Spread of Radioactive Contamination after a Radiological Dispersion Event
ASTM F 2731-11 : Standard Test Method for Measuring the Transmitted and Stored Energy of Firefighter Protective Clothing Systems
ASTM D 2731-07(2012) : Standard Test Method for Elastic Properties of Elastomeric Yarns (CRE Type Tensile Testing Machines)
ASTM D 2732-08 : Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
ASTM E 2732-11 : Standard Practice for Responder Family Support Service
ASTM F 2732-11 : Standard Practice for Determining the Temperature Ratings for Cold Weather Protective Clothing
ASTM E 2733-10 : Standard Guide for Investigation of Equipment Problems and Releases for Petroleum Underground Storage Tank Systems
ASTM F 2733-09 : Standard Specification for Flame Resistant Rainwear for Protection Against Flame Hazards
ASTM E 2734/E 2734M-10 : Standard Specification for Dimensions of Knife-Edge Flanges
ASTM D 2734-09 : Standard Test Methods for Void Content of Reinforced Plastics
ASTM F 2734-08 : Standard Practice for Testing the Shelf Life of Ink Jet Printer Cartridges
ASTM F 2735-09 : Standard Specification for Plastic Insert Fittings For SDR9 Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing
ASTM E 2735-14 : Standard Guide for Selection of Calibrations Needed for X-ray Photoelectron Spectroscopy (XPS) Experiments
ASTM F 2736-13 : Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe
ASTM E 2736-10 : Standard Guide for Digital Detector Array Radiology
ASTM E 2737-10 : Standard Practice for Digital Detector Array Performance Evaluation and Long-Term Stability
ASTM D 2737-12A : Standard Specification for Polyethylene (PE) Plastic Tubing
ASTM F 2737-11 : Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units
ASTM E 2738-13E1 : Standard Practice for Digital Imaging and Communication Nondestructive Evaluation (DICONDE) for Computed Radiography (CR) Test Methods
ASTM D 2739-97(2010) : Standard Test Method for Volume Resistivity of Conductive Adhesives
ASTM F 2739-08 : Standard Guide for Quantitating Cell Viability Within Biomaterial Scaffolds
ASTM E 2739-10 : Standard Specification for Personnel Decontamination System to be Used During a Chemical Event
ASTM E 2740-12E1 : Standard Specification for Trash Receptacles Subjected to Blast Resistance Testing
ASTM E 2741-11 : Standard Specification for Evaluation and Selection of Destinations for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM E 2742-11 : Standard Specification for Evaluation and Selection of Exhibits for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM D 2743-68(2010) : Standard Practices for Uniformity of Traffic Paint Vehicle Solids by Spectroscopy and Gas Chromatography
ASTM F 2743-11 : Standard Guide for Coating Inspection and Acute Particulate Characterization of Coated Drug-Eluting Vascular Stent Systems
ASTM E 2743-11 : Standard Specification for Evaluation and Selection of Transportation for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM E 2744-10 : Standard Test Method for Pressure Calibration of Thermal Analyzers
ASTM F 2745-11 : Standard Specification for Required Product Information to be Provided with an Airplane
ASTM E 2745-11 : Standard Specification for Evaluation and Selection of Audio Visual (AV) and Production for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM D 2745-00(2008) : Standard Test Method for Relative Tinting Strength of White Pigments by Reflectance Measurements
ASTM F 2746-12 : Standard Specification for Pilot’s Operating Handbook (POH) for Light Sport Airplane
ASTM E 2746-11 : Standard Specification for Evaluation and Selection of Communication and Marketing Materials for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM D 2746-07(2013) : Standard Test Method for Staining Tendency of Asphalt (Stain Index)
ASTM F 2747-10 : Standard Guide for Construction of Sand-based Rootzones for Golf Putting Greens and Tees
ASTM E 2747-11 : Standard Specification for Evaluation and Selection of Onsite Offices for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM E 2748-12A : Standard Guide for Fire-Resistance Experiments
ASTM F 2748-08 : Standard Specification for Low Energy Air Guns (Less Than 1 Joule)
ASTM E 2749-10(2014) : Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
ASTM F 2749-09 : Standard Test Method for Determining the Effects of Creasing a Membrane Switch or Assembly
ASTM D 2749-13 : Standard Symbols for Dimensions of Plastic Pipe Fittings
ASTM E 2750-13E1 : Standard Guide for Extension of Data from Penetration Firestop System Tests Conducted in Accordance with ASTM E814
ASTM F 2750-09 : Standard Test Method for Determining the Effects of Bending a Membrane Switch or Assembly
ASTM E 2751/E 2751M-13 : Standard Practice for Design and Performance of Supported Laminated Glass Walkways
ASTM F 2751-09 : Standard Guide for Training of Support Level Land Rescue Team Member (LRT-Support) Member
ASTM D 2752/D 2752M-88(2011)e1 : Standard Test Methods for Air Permeability of Asbestos Fibers
ASTM E 2752-10 : Standard Guide for Evaluation of Residual Effectiveness of Antibacterial Personal Cleansing Products
ASTM F 2752-09(2014) : Standard Guide for Training for Level I Rope Rescue (R1) Rescuer Endorsement
ASTM E 2753-10 : Standard Specification for <span class=”italic”>Eretmocerus eremicus</span> Rose and Zolnerowich (<span class=”bdit”>Hymenoptera: Aphelinidae</span>)
ASTM F 2753-10 : Standard Practice to Evaluate the Effect of Dynamic Rolling Load over Resilient Floor Covering System
ASTM F 2754/F 2754M-09(2013) : Standard Test Method for Measurement of Camber, Cast, Helix and Direction of Helix of Coiled Wire
ASTM D 2754-10 : Standard Specification for High-Temperature Glass Cloth Pressure-Sensitive Electrical Insulating Tape
ASTM E 2754-10 : Standard Specification for <span class=”italic”>Delphastus catalinae</span> (Horn) (Coleoptera:Coccinellidae)
ASTM E 2755-10 : Standard Test Method for Determining the Bacteria-Eliminating Effectiveness of Hand Sanitizer Formulations Using Hands of Adults
ASTM F 2755-14 : Standard Safety Specification for Cautionary Labeling of Inflatable Air Mattresses
ASTM E 2756-10 : Standard Terminology Relating to Antimicrobial and Antiviral Agents
ASTM D 2756-07(2012) : Standard Test Method for Weight Loss of Electrical Insulating Varnishes
ASTM F 2756-11 : Standard Test Method for Determining Energy Consumption of Vacuum Cleaners
ASTM F 2757-09 : Standard Guide for Home Laundering Care and Maintenance of Flame, Thermal and Arc Resistant Clothing
ASTM E 2758-10 : Standard Guide for Selection and Use of Wideband, Low Temperature Infrared Thermometers
ASTM D 2758-94(2009) : Standard Test Method for Engine Coolants by Engine Dynamometer
ASTM E 2759-10 : Standard Practice for Highway Traffic Monitoring Truth-in-Data
ASTM D 2759-00(2010) : Standard Practice for Sampling Gas from a Transformer Under Positive Pressure
ASTM F 2759-11 : Standard Guide for Assessment of the Ultra High Molecular Weight Polyethylene (UHMWPE) Used in Orthopedic and Spinal Devices
ASTM E 2760-10e2 : Standard Test Method for Creep-Fatigue Crack Growth Testing
ASTM F 2760-09 : Standard Practice for Testing Ink Jet Cartridge Latency (Start-Up)
ASTM F 2761-09(2013) : Medical Devices and Medical Systems – Essential safety requirements for equipment comprising the patient-centric integrated clinical environment (ICE) – Part 1: General requirements and conceptual model
ASTM E 2762-10(2014) : Standard Practice for Sampling a Stream of Product by Variables Indexed by AQL
ASTM F 2762-11E1 : Standard Specification for 12 to 30 in. (300 to 750 mm) Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
ASTM E 2763-10 : Standard Practice for Computer Forensics
ASTM F 2763-11 : Standard Specification for 30 to 60 in. [750 to 1500 mm] Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications
ASTM F 2764/F 2764M-11ae2 : Standard Specification for 30 to 60 in. [750 to 1500 mm] Polypropylene (PP) Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications
ASTM D 2764-99(2009) : Standard Test Method for Dimethylformamide-Insoluble (DMF-I) Content of Tar and Pitch
ASTM E 2764-11 : Standard Practice for Uncertainty Assessment in the Context of Seized-Drug Analysis
ASTM E 2765-11 : Standard Practice for Use of Image Capture and Storage Technology in Forensic Document Examination
ASTM D 2765-11 : Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
ASTM F 2765-09 : Standard Specification for Total Lead Content in Synthetic Turf Fibers
ASTM E 2766-13 : Standard Practice for Installation of Roof Mounted Photovoltaic Arrays on Steep-Slope Roofs
ASTM D 2766-95(2009) : Standard Test Method for Specific Heat of Liquids and Solids
ASTM F 2766-11 : Standard Test Method for Boat Barriers
ASTM E 2767-13 : Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) for X-ray Computed Tomography (CT) Test Methods
ASTM F 2767-12 : Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution
ASTM E 2768-11 : Standard Test Method for Extended Duration Surface Burning Characteristics of Building Materials (30 min Tunnel Test)
ASTM F 2768-09 : Standard Specification for Modified Stub ACME Thread Joint with Elastomeric Seal in Plastic Piping Components
ASTM F 2769-10 : Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems
ASTM E 2769-13 : Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading
ASTM F 2771-10 : Standard Test Method for Determining the Luminance Curve of an Electroluminescent Lamp at Ambient Conditions
ASTM E 2771-11E1 : Standard Terminology for Homeland Security Applications
ASTM E 2772-13E1 : Standard Specification for Evaluation and Selection of Accommodations for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM F 2772-11 : Standard Specification for Athletic Performance Properties of Indoor Sports Floor Systems
ASTM E 2773-11 : Standard Specification for Evaluation and Selection of Food and Beverage for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM F 2773-13 : Standard Practice for Transfilling Compressed Air or Nitrogen and Safe Handling of Small Paintball Cylinders
ASTM D 2774-12 : Standard Practice for Underground Installation of Thermoplastic Pressure Piping
ASTM E 2774-11 : Standard Specification for Evaluation and Selection of Venues for Environmentally Sustainable Meetings, Events, Trade Shows, and Conferences
ASTM F 2774-09 : Standard Practice for Manufacturing Quality Control of Consumer Trampoline Bed Material
ASTM E 2775-11 : Standard Practice for Guided Wave Testing of Above Ground Steel Pipework Using Piezoelectric Effect Transduction
ASTM D 2777-13 : Standard Practice for Determination of Precision and Bias of Applicable Test Methods of Committee D19 on Water